Red-lion DP5T Manuel d'utilisateur télécharger pdf (Page 10)

5.0 PROGRAMMING THE METER

OVERVIEW

PROGRAMMING MENU

DISPLAY MODE

The meter normally operates in the Display Mode. In this mode, the meter

displays can be viewed consecutively by pressing the DSP key. The

annunciators to the left of the display indicate which display is currently shown;

Max Value (MAX), Min Value (MIN), or Totalizer Value (TOT). Each of these

displays can be locked from view through programming. (See Module 3) The

Input Display Value is shown with no annunciator.

PROGRAMMING MODE

Two programming modes are available.

Full Programming Mode permits all parameters to be viewed and modified.

Upon entering this mode, the front panel keys change to Programming Mode

operations. This mode should not be entered while a process is running, since

the meter functions and User Input response may not operate properly while

in Full Programming Mode.

Quick Programming Mode permits only certain parameters to be viewed

and/or modified. When entering this mode, the front panel keys change to

Programming Mode operations, and all meter functions continue to operate

properly. Quick Programming Mode is configured in Module 3. Throughout

this document, Programming Mode (without Quick in front) always refers to

“Full” Programming Mode.

PROGRAMMING TIPS

The Programming Menu is organized into nine modules (See above). These

modules group together parameters that are related in function. It is

recommended to begin programming with Module 1 and proceed through each

module in sequence. If lost or confused while programming, press the DSP key

to exit programming mode and start over. When programming is complete, it is

recommended to record the meter settings on the Parameter Value Chart and

lock-out parameter programming with a User Input or lock-out code. (See

Modules 2 and 3 for lock-out details.)

FACTORY SETTINGS

Factory Settings may be completely restored in Module 9. This is a good

starting point if encountering programming problems. Throughout the module

description sections which follow, the factory setting for each parameter is

shown below the parameter display. In addition, all factory settings are listed on

the Parameter Value Chart following the programming section.

ALTERNATING SELECTION DISPLAY

In the module description sections which follow, the dual display with

arrows appears for each programming parameter. This is used to illustrate the

display alternating between the parameter (top display) and the parameter's

Factory Setting (bottom display). In most cases, selections or value ranges for

the parameter will be listed on the right.

Indicates Program Mode Alternating Display

Parameter

Selection/Value





STEP BY STEP PROGRAMMING INSTRUCTIONS:

PROGRAMMING MODE ENTRY (PAR KEY)

The Programming Mode is entered by pressing the PAR key. If this mode is

not accessible, then meter programming is locked by either a security code or a

hardware lock. (See Modules 2 and 3 for programming lock-out details.)

MODULE ENTRY (ARROW & PAR KEYS)

Upon entering the Programming Mode, the display alternates between 

and the present module (initially ). The arrow keys (F1S and F2T) are used

to select the desired module, which is then entered by pressing the PAR key.

PARAMETER (MODULE) MENU (PAR KEY)

Each module has a separate parameter menu. These menus are shown at the

start of each module description section which follows. The PAR key is pressed

to advance to a particular parameter to be changed, without changing the

programming of preceding parameters. After completing a module, the display

will return to  . From this point, programming may continue by selecting

and entering additional modules. (See MODULE ENTRY above.)

PARAMETER SELECTION ENTRY (ARROW & PAR KEYS)

For each parameter, the display alternates between the parameter and the

present selection or value for that parameter. For parameters which have a list

of selections, the arrow keys (F1S and F2T) are used to sequence through the

list until the desired selection is displayed. Pressing the

PAR key stores and

activates the displayed selection, and also advances the meter to the next

parameter.

NUMERICAL VALUE ENTRY (ARROW, RST & PAR KEYS)

For parameters which require a numerical value entry, the arrow keys can be

used to increment or decrement the display to the desired value. When an arrow

key is pressed and held, the display automatically scrolls up or scrolls down.

The longer the key is held, the faster the display scrolls.

The RST key can be used in combination with the arrow keys to enter large

numerical values, when the RST key is pressed along with an arrow key, the

display scrolls by 1000’s. Pressing the PAR key stores and activates the

displayed value, and also advances the meter to the next parameter.

PROGRAMMING MODE EXIT (DSP KEY or PAR KEY at  )

The Programming Mode is exited by pressing the DSP key (from anywhere

in the Programming Mode) or the PAR key (with   displayed). This will

commit any stored parameter changes to memory and return the meter to the

Display Mode. If a parameter was just changed, the PAR key should be pressed

to store the change before pressing the DSP key. (If power loss occurs before

returning to the Display Mode, verify recent parameter changes.)

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Red-lion DP5T Manuel d'utilisateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour ordinateurs Red-lion DP5T