4
LIMITED WARRANTY
The Company warrants the products it manufactures against defects in materials and workmanship
for a period limited to two years from the date of shipment, provided the products have been stored,
handled, installed, and used under proper conditions. The Company’s liability under this limited
warranty shall extend only to the repair or replacement of a defective product, at The Company’s
option. The Company disclaims all liability for any affirmation, promise or representation with
respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products
containing components manufactured by RLC and based upon personal injuries, deaths, property
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty
Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except
those expressly contained herein. The Customer acknowledges the disclaimers and limitations
contained herein and relies on no other warranties or affirmations.
DOUBLE WHEEL PIVOT INSTALLATION
(MBZM0002):
Note: It is recommended that double wheel ZMH’s be installed with the optional
Double Wheel Pivot. The pivot allows the unit to rotate freely to maintain
equal pressure on both wheels, accommodating uneven/angled surfaces and
mounting misalignment.
1. Thread the pivot clamp into the end of the ZMH’s clamp by hand until the
threads just bottom out then back out approximately 1 revolution to allow for
rotation after installation.
2. Slide the pivot clamp over a fixed Ø5/8" (Ø0.625 +0/-0.005") shaft. The
optional ZMH Mounting Bracket (MBZM0001) is shown in the picture.
3. While applying a load to the spring, securely tighten the two clamp bolts with
a 5/32" (supplied) or 4mm hex “L” key.
CONNECTOR EXIT ORIENTATION ADJUSTMENT:
1. Slide the ZMH over a Ø5/8" (Ø0.625 +0/-0.005") shaft and tighten the clamp
bolts with the supplied 5/32" hex “L” key.
2. Remove the measuring wheel(s) using the supplied 3/32" hex “L” wrench to
loosen the set screws.
3. Remove 6 screws (3 on each side) from the side plates using the supplied
7/64" hex “L” key.
4. Rotate body of encoder to desired orientation, aligning bolt pattern with one
of six unique positions (see inset drawing).
5. Replace side plate screws and measuring wheel(s), making sure to tighten
screws securely.
Apply Load
Pivot
Clamp
Threaded
Joint
Rotate
Body
Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
Red Lion Controls
China
Unit 302, XinAn Plaza
Building 13, No.99 Tianzhou Road
ShangHai, P.R. China 200223
Tel +86 21 6113 3688
Fax +86 21 6113 3683
Red Lion Controls
Europe
Softwareweg 9
NL - 3821 BN Amersfoort
Tel +31 (0) 334 723 225
Fax +31 (0) 334 893 793
Red Lion Controls
India
201-B, 2nd Floor, Park Centra
Opp 32 Mile Stone, Sector-30
Gurgaon-122002 Haryana, India
Tel +91 984 487 0503
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels