Red-lion ZMD - MINIATURE QUAD Manuel d'utilisateur télécharger pdf

ZMD INSTALLATION AND REMOVAL

Insert No. ZMDINST-X

Drawing No. LP0765

Effective 7/08

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

INSTALLATION

1. Remove the rubber cap and verify the set-screw in the spring adjustment

collar is loose. The ZMD pivot shaft should rotate easily by hand.

Note: To reverse Pivot Shaft orientation:

Remove c-clip, hold spring adjustment collar in place while removing

and reversing pivot shaft. Install c-clip.

2. Install the threaded end of the pivot shaft through the mounting bracket.

Install the washer and nut provided finger tight. The mounting bracket is

typically supplied by the customer and would vary from application to

application. The recommended hole diameter in the mounting bracket should

be just large enough for clearance of the 1/4" or 6 mm pivot shaft and

between 0.5" to 1.5" above the material surface.

3. Hold one end of the pivot shaft with a wrench while the nut is securely

tightened.

4. At this point the ZMD housing assembly should rotate easily around the pivot

shaft.

5. Rotate the housing so the measuring wheel is contacting the surface to be

measured. Insert the 3/32 hex L key into the setscrew on the spring

adjustment collar. Using the hex key arm for leverage, rotate the collar

around the pivot shaft in the direction necessary to increase the spring force

that holds the measuring wheel against the surface to be measured. While

maintaining pressure, tighten the set-screw very securely to avoid loss of

spring pressure. (A torque of 15-18 in-lbs is recommended, however a torque

wrench is not required as long as the set-screw is good and tight.)

Note: The spring adjustment collar should not be rotated so far that it

bottoms out against the internal stop or the ZMD will not have sufficient

travel to accommodate variations in the surface height of the material being

measured. For most applications the spring setting in it's mid range (about

2 pounds) is satisfactory. The spring force can be checked by carefully lifting

up on the wheel. You should be able to lift the wheel 1/8" to 1/4" off the

surface being measured. If not, repeat step 5.

6. Install the rubber cap.

REMOVAL

1. Remove the rubber cap.

2. Loosen the setscrew in the spring adjustment collar. The ZMD should rotate

easily around the pivot shaft.

3. Hold one end of the pivot shaft with a wrench while the lock nut is removed.

4. Remove the ZMD from the mounting bracket and install the washer and lock

nut on the shaft by hand.

Rotate to increase spring force

Set Screw in Spring

Adjustment Collar

Pivot Shaft

Rubber Cap

Hex “L” Key

C-Clip

Typical Mounting Bracket

Wrench on Pivot Shaft

Hex “L” Key

ZMD INSTALLATION AND REMOVAL 1

Résumé du contenu

Page 1 - ZMD INSTALLATION AND REMOVAL

ZMD INSTALLATION AND REMOVALInsert No. ZMDINST-XDrawing No. LP0765Effective 7/08Tel +1 (717) 767-6511Fax +1 (717) 764-0839www.redlion.netINSTALLATI

Plus de documents pour Accessoires pour ordinateurs Red lion ZMD - MINIATURE QUAD

Voir le document Red-lion ZMD - MINIATURE QUAD Manuel d'utilisateur

Red-lion ZMD - MINIATURE QUAD Manuel d'utilisateur (2 pages)

Commentaires sur ces manuels

Pas de commentaire

Red-lion ZMD - MINIATURE QUAD Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour ordinateurs Red-lion ZMD - MINIATURE QUAD. Red Lion ZMD - MINIATURE QUAD User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Accessoires pour ordinateurs Red lion ZMD - MINIATURE QUAD

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour ordinateurs Red-lion ZMD - MINIATURE QUAD